I am trying to authencate users accessing FAS 8040 using DC.
Getting this error:
Error: Machine account creation procedure failed ...
Vserver 'ADSVM' [ 1] Failed to connect to X.X.X.X for DNS: No route to host [ 1]
Error: command failed: Failed to create the Active Directory machine account "XXXX". Reason: SecD Error: no server available.
Can anyone help?
Hi
First, i would like to know if limitations are from FAS or CDOT ?
for
max svm, snapshot export policy, qtree, lif
secondly, i would like to know where i can found limitation specs for max svm, max snapshot per volume, max export policy, qtree, lif , for cdot 8.2.x FAS8080
thanks for help.
regards
Hi guys,
I have the below command to create a policy for audit logging.
vserver audit create -vserver <vserver name> -destination <Unix Path> -rotate-schedule-minute <minute of the hour> -rotate-limit <no.of log files>
What is the destination here ?
its says <unix Path> but what exactly is a unix path?
In our system we have CIFS protocol licensing only. Therefore I cannot create a nfs export to facilitate a unix path.
can you please guide me?
Also do you guys have something like a general case, sample command in use for the above?
hi there,
sorry it has been a while...
I fixed the problem by reconfiguring the entire setup. It was because I was given a bad gateway ip address. once replaced it, everything started to work.
Hi,
For Clustered Data ONTAP 8.2.x Maximum Configurations Guide refer, https://fieldportal.netapp.com/content/201317?assetComponentId=20141
For Software Storage Platform Mixing Rules refer,https://library.netapp.com/ecm/ecm_get_file/ECMP1644424
Thanks
Hi,
For Clustered Data ONTAP 8.3 CIFS and NFS Auditing Guide refer https://library.netapp.com/ecm/ecm_download_file/ECMLP2426796
Thanks
When we are performing a netapp 8.3 NDMP backup with a backup software, We received error:
"DUMP: Message from Write Dirnet: Interrupted system call"
Not sure about the reason, any ideas?
Thank you very much.
Hi,
ONTAP 9.1rc1
Scenario:
volume A contains 2 qtrees: tree1 and tree2
If I create a file in qtree1, and then try to create a hard link in tree2 for the file, it will complain "Invalid cross-device link." So it seems to me a qtree is like a volume having its own file system. In other words, say in qtree1 a file has inode 11111, it's possible in qtree2 there a file also having inode 11111. Is it correct?
I know hard links should be avoided in general but unfortunately the data set i am dealing with already have alot of hard links and I need to migrate them from isilon to NetApp.
Thanks,
Hi there!
In cDOT 8.3.2P4 the following happens:
When deleting files or folders in a CIFS-Share they reappear when deleting them. After some time the files or folders vanish completely.
What can I do, to get rid of deletes files immediately?
I do not notice any conspicuously in CIFS options.
Thanks in advance.
Hey community,
i just have a little question for you. I tried to expand a LUN on our AFF 8040 cDot system, but the operation failed. I've got the following error message by the SnapDrive e-mail notifier:
Header:
-----------
Data ONTAP LUN Manager Auto Notification - LUN event : Error
Text:
------
LUN Manager Event Detail:
Computer Name: xxxxxx
Event ID: 125
Type: Error
Category: LUN event
Description: Failed to expand the LUN by 51189 MB. Failure in expanding NTFS file system on the disk.
LUN Name = Daten
Storage Path = /vol/xxxxxx_data/xxxxxxx_E/ Protocol Type = HTTP Storage System Name = SVM12
Error code : Error 0x6d occured. Description is not found.
Here some more details:
Storage system: AFF8040HA (cDot 8.3.2P5)
Server system: Windows Server 2008R2 (latest patches)
SnapDrive: SnapDrive 7.1.3P1
Do you have any ideas, where's the problem? Could this might be the problem, that it isn't possible to expand the LUN more than its 10x size?
Thanks for helping.
Greets
tbshpgn
Hi,
I've juste installed MPIO (Round Robin) et DSM on my WS2012R2 for an Hyper-V cluster.
Thanks to these videos :
https://www.youtube.com/watch?v=vVAir7tUZK8
https://www.youtube.com/watch?v=uLMknaRoYg0
But when I check the DSM Management MMC, I don't know why the state is "Active/Non Optimized".
Regards.
Hi,
Did you manage to solve this? I'm facing the same problem and I can't find a solution to this problem...
Those commands are not supported. Instead, use 'system configuration backup' in the advanced priviledge level.
cdot::system configuration backup*> ? copy *Copy a configuration backup create *Create a configuration backup delete *Delete a configuration backup download *Download a configuration backup rename *Rename a configuration backup settings> *The settings directory show *Show configuration backup information upload *Upload a configuration backup cdot::system configuration backup*>
Also see the section titled "Backing up and restoring cluster configurations (cluster administrators only)" in the system administration guide.
Kala -
NetApp uses ALUA to communitcate path status with the host.
Paths to interfaces on the node hosting the LUN are reported as Active/Optimized.
Paths to interfaces on any other node not hosting the LUN are reported as Active/Non-Optimized.
Did you truncate the output ?
Do you have interfaces configured on the node hosting the LUN ?
I hope this response has been helpful to you.
At your service,
Eugene E. Kashpureff, Sr.
Independent NetApp Consultant http://www.linkedin.com/in/eugenekashpureff
Senior NetApp Instructor, FastLane US http://www.fastlaneus.com/
(P.S. I appreciate 'kudos' on any helpful posts.)
Hi roombabu,
The UNIX path is just a path within your name space. I recommend creating a new volume (and a qtree if required) for storing the audit logs.
I implemented audit logging for a customer a few weeks ago, here are the steps:
The following links might be useful:
How to set up CIFS auditing with clustered Data ONTAP
Clustered Data ONTAP CIFS Auditing Quick Start Guide
I hope this helps!
Dirk
I have a cluster running OnTap 8.3.2
The cluster and node management network interfaces are active
and I can ssh to them.
The web services are up and running
Cluster::> sys ser web show
(system services web show)
External Web Services: true
Status: online
HTTP Protocol Port: 80
HTTPs Protocol Port: 443
TLSv1 Enabled: true
SSLv3 Enabled: false
SSL FIPS 140-2 Enabled: false
I am using I.E. 8
When I attempt to access the filer via the GUI (using https),
using the cluster IP I get the security certificate error,
click continue to this website
The URL is https://nnn.nnn.nnn.nnn/sysmgr/SysMgr.html
The screen stays white and I am not prompted for the credentials.
Any ideas ?
Thanks in Advance
No ideas?
Mark -
IE 8 is not supported.
See the supported browsers here:
https://library.netapp.com/ecmdocs/ECMLP2348067/html/GUID-74BC2023-C464-4958-88E0-B758B6003F9B.html
I hope this response has been helpful to you.
At your service,
Eugene E. Kashpureff, Sr.
Independent NetApp Consultant http://www.linkedin.com/in/eugenekashpureff
Senior NetApp Instructor, FastLane US http://www.fastlaneus.com/
(P.S. I appreciate 'kudos' on any helpful posts.)
